Antimony Opie manual
Antimony Opie is a polyphonic synthesizer for the Mac and iPad, as an app and as an Audio Unit plug-in for Logic, GarageBand and other hosts. This manual covers playing it, the panel, the sounds, and using it in Logic.
Playing
- Keys: any MIDI keyboard, the on-screen keyboard, or the computer keys in the app (A to ; play notes, Z and X change octave). The minus and plus buttons beside "From C4" move the on-screen keyboard by an octave.
- Wheels: Pitch Bend and Modulation sit above the keys; the mod wheel adds vibrato on most sounds.
- MIDI input at the top of the app counts the keyboards and other sources it hears. The app listens on every channel.
- MIDI clock: when outside gear sends MIDI clock, the app follows its tempo, and its Start and Stop, for the arpeggiator and a synced delay. Without clock, the Tempo setting applies.
Sounds
- The library on the left lists 70 factory sounds by category: Bass, Brass, Keys, Lead, Pad, Strings, Pluck & Bell, Percussion, Motion and Effects. Each has two words describing it. Search matches names, categories and those words ("drum", "warm", "echo").
- Edited and Saved at the top compare your changes with the sound as it was loaded.
- Save keeps your sound under a name of your own, in My Sounds. Factory sounds never change. Inside a host, saved sounds also appear in the host's own preset menu.
- Loading a sound never changes the number of voices or the tempo; those belong to the instrument.
The panel
The middle of the window draws one voice as the signal flows: oscillators into the mixer, the mixer into the filters, the filters into the amplifier, then the effects and the output. Click any block to edit it on the right. Every value can be typed: click it and enter "1.2k", "350 ms", "-3" or "40%".
- Oscillators 1 and 2: saw, triangle or pulse, with octave, semitone and fine tuning, pulse width and glide. Oscillator 2 can sync either way and frequency-modulate Oscillator 1.
- Mixer: levels for both oscillators, ring modulation and noise.
- MM filter: a 4-pole ladder lowpass. OB filter: a 2-pole lowpass, bandpass or highpass. The menu under them chooses parallel (both hear the mixer) or series (the OB hears the MM). Drag across a filter's picture to set cutoff, up and down for resonance.
- Amplifier: shaped by Envelope 4; Velocity sets how much playing harder makes it louder.
- Effects: a stereo chorus, then a delay. Delay Sync sets the echo in note lengths at the tempo; Free uses Delay Time. Ping-Pong bounces echoes left and right; Tone darkens each one.
- Output: Volume, and Boost for sounds that need more level, such as drums. The meter shows each channel with a peak line; the light above it turns red when the mix drives the output's soft clipper, so turn Volume down for a clean sound.
- Arpeggiator: plays the keys you hold as a pattern: Up, Down, Up & Down, Random or As Played, at a note length, over one to four octaves. Gate sets how long each note sounds. Latch keeps the pattern going after you let go; play a new chord to replace it.
- Part B: a second sound in the same instance. Choose any factory sound, its level and octave. Layer plays it with the main sound on every key; Split gives it the keys below the split point and the main sound the rest, say a bass under a lead. Part B has its own voices, effects and arpeggiator, as its sound sets them, and follows the same tempo.
- Voices: Poly plays a voice per note; Rotate cycles through voices for a livelier sound; Unison stacks every voice on one note; Stack plays two voices per note. Voices sets how many voice cards play, from 2 to 12.
- Performance: unison detune, analog drift (small differences between voices, as on real hardware) and the pitch bend range.
Modulation
Envelopes 1 to 4 and LFOs 1 to 3 sit under the signal path. Envelope 1 always moves the MM cutoff, Envelope 2 the OB cutoff and Envelope 4 the amplifier; Envelope 3 is free. To make any of them move something else, drag its card onto a block, or open the Matrix and fill a slot: a source, a destination and an amount. There are twelve slots.
In Logic
- Insert it from AU Instruments › Humbug Mountain › Antimony Opie on a software instrument track. The plug-in window is the same panel and scales to fit.
- Logic saves the sound with the project. A program change in a region picks a factory sound, and the plug-in's header names it.
- The arpeggiator and a synced delay follow the song's tempo and bars while Logic plays.
- To bring in a MIDI file, use File › Import › MIDI File, then check every track uses Antimony Opie. Support explains how to move any part Logic put on its General MIDI device.
Troubleshooting
- No sound in the app: check the output device in System Settings › Sound, and that the Volume in the Output block isn't at zero.
- The clip light stays red: the sound or the chord is too loud for the output; lower Volume.
- Logic says the plug-in isn't available: quit Logic and open it again; Logic looks for plug-ins when it starts.